| |
| Clearoma®
Institution/Industry |
|
CANADA-WHMIS
PRODUCT: CLEAROMA
CLEAROMA Industries
FOR INFORMATION CALL: 1-250-491-0740
EMERGENCY:Your Local Poison Control Center
ABBREVIATIONS USED:
N/Ap - Not Applicable
N/Av - Not Available
N/D - Not Determined
N/E - Not Established
DATE OF ISSUE: 01/01/2010
HEALTH.....2
FLAMMABILITY..1
REACTIVITY...0
SECTION 1 - IDENTIFICATION AND
GENERAL INFORMATION
PRODUCT ID:
Clearoma™
CAS
NUMBER: N/Ap
CHEMICAL NAME:
N/Ap
TSCA INVENTORY:
N/Ap
CHEMICAL FAMILY: Fragrance
Compound
SYNONYMS:
N/Ap
MOLECULAR WEIGHT: N/Ap
MOLECULAR FORMULA: N/Ap
SECTION 2 - HAZARDOUS INGREDIENT(S)
This compound is a complex mixture
of raw materials. Certain of the ingredients may be considered
"controlled products" as defined by WHMIS criteria. Those components
present at 1% or greater which may influence the hazard potential
of this untested mixture are classified as follows:
INGREDIENTS:
92.30% Hydroxy Compound
3.20% Surfactant
SECTION 3 - PHYSICAL DATA
BOILING POINT:
N/D
MELTING POINT:
N/D
SPECIFIC GRAVITY:
.9940 at 25 C
REFRACTIVE INDEX: N/D
ALCOHOL CONTENT: N/D
WATER CONTENT:
N/D
VAPOR PRESSURE:
49.202 MM HG
CALCULATED WITH 99% AVAILABLE
DATA
SOLUBILITY IN WATER: SOLUBLE
PHYSICAL STATE: LIQUID
APPEARANCE:
GREEN BLUE
CHARACTERISTIC ODOR
SECTION 4 - FIRE, EXPLOSION AND REACTIVITY DATA
TYPE OF HAZARD:
NONE KNOWN
FLASH POINT:
205 F
METHOD USED:
CC
LOWER FLAMMABILITY LIMIT:
N/D
UPPER FLAMMABILITY LIMIT:
N/D
EXTINGUISHING MEDIA:
Carbon Dioxide,
Dry Chemical or Universal-type Foam.
SPECIAL FIRE FIGHTING PROCEDURES:
Use of self contained breathing apparatus and protective
clothing is
recommended.
MATERIALS/CONDITIONS TO AVOID:
NONE KNOWN
UNUSUAL FIRE, EXPLOSION AND STABILITY HAZARDS:
Sealed containers may build up pressure at high temperatures.
Keep containers
cool whenever possible.
REACTIVITY DATA:
This product presents no significant reactivity hazard.
It is stable and will not
react violently with
water. Hazardous polymerization
will not occur. Avoid contact or contamination
with strong acids, alkalis
and/or oxidizing agents.
SECTION 5 - HEALTH HAZARD DATA
This material contains no ingredient(s) present at 0.1%
or greater, which
Is listed as a carcinogen or potential
carcinogen by IARC, NTP or OSHA.
AN INGREDIENT IN THIS PROPRIETARY MIXTURE HAS THE
FOLLOWING:
EXPOSURE LIMITS:
OSHA PEL: 400.00 PPM
980.00 MG/M3 VIA INHALE
ACGIH TLV: 400.00 PPM
983.00 MG/M3 VIA INHALE
OSHA STEL: N/E
ACGIH STEL: 500.00 PPM
1230.00 MG/M3 VIA INHALE
ANIMAL ACUTE TOXICITY DATA:
ORAL LD50: Mg/KG
INHALATION LC50:
N/D
DERMAL LD50:
Mg/KG
HEALTH HAZARD (ACUTE AND
CHRONIC)
THIS PRODUCT IS A MIXTURE AND HAS NOT BEEN TESTED FOR HEALTH HAZARDS. THE HEALTH HAZARD
INFORMATION PRESENTED BELOW IS PROVIDED IN ACCORDANCE WITH 29
CFR 1910.1200 AND IS BASED ON THE TESTING OF INDIVIDUAL COMPONENTS WHICH
HAVE BEEN SHOWN TO CAUSE THE FOLLOWING HEALTH EFFECTS WHEN TESTED
AT HIGHER CONCENTRATIONS OR AT FULL STRENGTH:
IN ANIMALS:
INGESTION:
CNS effects Serious health effects, toxic
INHALATION:
NONE KNOWN
SKIN
CONTACT: NONE KNOWN
IRRITATION
SKIN: Irritation
IRRITATION
EYE: Irritation
NOTE: The relevancy of the above
effects to humans is unknown.
IN HUMANS:
INGESTION:
NONE KNOWN
INHALATION:
CNS effects, irritation of throat and lungs.
SKIN
CONTACT NONE KNOWN
IRRITATION
SKIN: Irritation
IRRITATION
EYE: Irritation
NOTE: For additional information
see SECTION 11
MEDICAL CONDITIONS GENERALLY AGGRAVATED
BY EXPOSURE: NONE KNOWN
SECTION 6 - EMERGENCY FIRST AID
PROCEDURES
EYE
CONTACT:
Immediately flush eyes with large
quantities of clean water for at least 15 minutes. Call a physician
immediately.
SKIN CONTACT:
Remove any contaminated clothing
or shoes. Thoroughly wash affected areas with soap and water.
Flush with large quantities of clean water. If irritation develops
or persists, call a physician.
INHALATION:
Remove to fresh air and contact
a physician immediately.
INGESTION:
"DO NOT" induce vomiting. Administer
water and call a physician or local Poison Control Center immediately.
SECTION 7 - PERSONAL PROTECTION
EYES:
In general, the use of safety
glasses with side-shields is recommended. If the material is to
be handled in a manner where splashing may occur, the use of splash
goggles or a face shield and goggles is recommended.
RESPIRATORY:
In well-ventilated areas respiratory
protection is not normally required. In confined or poorly ventilated
areas or if material is toxic by inhalation, the use "NIOSH"-approved
respiratory protection is recommended.
EQUIPMENT & APPAREL:
The use of chemical resistance
gloves is recommended. Acceptable industrial hygiene practices
should be maintained by limiting exposure to the material. Wash
immediately before eating or after any contact with the material.
Thoroughly wash any contaminated clothing or shoes before reuse.
VENTILATION:
Ventilation, which meets accepted
standards, is recommended. Use exhaust fan if necessary.
SECTION 8 - SPILL, LEAK AND WASTE DISPOSAL PROCEDURES
SPILL OR RELEASE:
Contain spilled material. Avoid
open flames or other sources of ignition. Avoid inhalation of
vapors and contact with skin and eyes. In a confined or poorly
ventilated area, the use of "NIOSH" approved respiratory protection
is recommended. Cover the spilled material with an inert, non-combustible
absorbent material and remove to an approved disposal container.
If required, report the spill to appropriate authorities.
DISPOSAL:
Dispose of in accordance with
all current applicable local, provincial and
federal regulations.
SECTION 9 - STORAGE AND HANDLING
It is recommended that this material
be stored in a cool, well-ventilated area away from open flames
or other sources of ignition.
When handling this material, good
industrial hygiene practices should be followed in order to avoid
inhalation and contact with skin and eyes.
SECTION 10 - SARA TITLE III
SECTION 313
This substance contains no materials
subject to the reporting requirements of SARA TITLE III SECTION 313.
SECTION 11 - ADDITIONAL INFORMATION
Regarding Flammability, all figures in this report are
in reference to a base strength solution of Clearoma™. Due to the
mixture ratios of the finished product, the effects of these materials
would be presumed to be mitigated in the mixture.
Regarding Health Hazards, all figures in this report
are in reference to a base strength solution of Clearoma™. Due
to the mixture ratios of the finished product, the effects
of these materials would be presumed to be mitigated in the
mixture.
THIS MATERIAL SAFETY DATA SHEET IS INTENDED TO MEET THE SPECIFIC REQUIREMENTS
OF 29 CFR 1910.1200 AND SHOULD BE USED ACCORDINGLY. WHILE THE INFORMATION HAS BEEN OBTAINED FROM SOURCES BELIEVED TO BE ACCURATE AND
RELIABLE, NO WARRANTY, EXPRESSED OR IMPLIED, CAN BE MADE WITH
REGARD TO ITS COMPLETENESS, CORRECTNESS OR ACCURACY. ANY USERS
OR HANDLERS OF THIS PRODUCT WHO ARE NOT UNDER THE DIRECT CONTROL OF Clearoma™ Products Inc.
ARE RESPONSIBLE FOR EVALUATING THIS INFORMATION IN LIGHT OF THEIR PARTICULAR
SITUATION AND ARE RESPONSIBLE FOR ALL LOSSES, DAMAGES OR EXPENSES THAT RESULT WHILE THIS MATERIAL
IS UNDER THEIR CONTROL. IT IS ALSO THE RESPONSIBILITY OF THE USERS
AND HANDLERS TO OBSERVE ANY AND ALL LAWS AND REGULATIONS (FEDERAL, STATE AND LOCAL) CONCERNING THE TRANSPORTATION, USE, HANDLING,
STORAGE AND DISPOSAL OF THIS PRODUCT.
|
